ARRIS_TM_1602

trying to get full shell
tried a few things to work around
manually messing with dump

AC_BOOT
POST: 0xb03
wdt: reset type = 0, reset reason = 0
POST: 0xc02
cefdk_rom_base_addr: 0x002e0000
POST: 0xc1f
wdt: acboot win2 end, counter=974874
POST: 0xf02
Warning: No device found in chip select 0
Spi Flash Init Failed and disable SPI Fl
Intel® Consumer Electronics Firmware Development Kit (Intel® CEFDK)
Copyright © 1999-2012 Intel Corporation. All rights reserved.
Build Time (04/18/14 11:26:13).
POST: 0xf07
Set flash layout to Arris 128MB Phison layout
POST: 0xf19
Waiting for 5 sec for DOCSIS PLL1 ready...
DOCSIS PLL1 ready
Warning: invalid 'Active AID', ACTIMAGE is not set.
emmc_rd(0x280000, 0x9c00, 0x800) fail
POST: 0xfa0
SMM: Ok
POST: 0xf24
ACPI Init: finished with table region from 00011ab0 to 00018000
acpi: Created tables at 00011ab0-00018000
POST: 0xf29
CEFDK Version : ARRIS build 1602:3.01.14 (SMP enabled)
Built from SDK : IntelCE-0.35.14165.344312
8051 Firmware : A0-1.1.8 build E 0x1EF
8051 FW I/O Module :
Silicon Stepping : B2
Silicon SKU : 0x039
Board Set As : Harbor Park
CPU Threads : 2
CPU Multiplier : 6
CPU Bus Speed : 100 MHz
Memory Size : 256 MB
Memory Type & Speed : x16 DDR3-1333 (10-10-10)
Trusted Boot : Untrusted
Boot Mode : eMMC-NAND (STRAPS)
emmc_rd(0x280000, 0x4ed04, 0x200) fail
emmc_rd(0x280200, 0x4ed04, 0x200) fail
emmc_rd(0x280400, 0x4ed04, 0x200) fail
emmc_rd(0x280600, 0x4ed04, 0x200) fail
Error reading MAC address from boot flash, plat_param entry is not found in MFH. Please add a MAC address by command mfh add lan_eeprom.
Registered net controller: e1000
mac address is not correct, nothing to do here!

================================================
WARNING:
Please make sure the board type and DOCSIS DDR offset/size are set correctly,
otherwise DOCSIS subsystem won't boot!
If not sure, please use "settings" shell command to show the setup menu,
then check "Advanced Features".
================================================

Press 'Enter' within 0 seconds to disable automatic boot.
Hit a key to start the shell...
emmc_rd(0x280000, 0x9c00, 0x800) fail
emmc_rd(0x290a00, 0x5007c66, 0x800) fail
Running auto script...
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell>
shell> help
bootata - Boots from the primary master ATA device.
ymodem - Receive a file from serial using YMODEM.
lspci - Displays PCI device info.
ord[2|4] - Read or write to memory.
pci[2|4] - Read or write to PCI configuration space.
port[2|4] - Read or write to I/O port.
goto - goto to specific IP to run code.
crc32 - compute crc32 sum of a bulk memory
netserver - net server service for external clients
ramdisk - set ramdisk start address and length
delay - delay some time
mmap - Displays a system memory map.
bootkernel - Boot Linux kernel from flash.
mfh - manage the MFH on flash devices
md5 - Calculate a MD5 sum for an input data string.
emmc - Auxiliary shell command to handle eMMC
spi_flash - Auxiliary shell command to handle SPI Flash
aid - manage the Active Image Designator
8051 - 8051 specific commands
sha - Calculate a SHA sum for an input data string.
gpio - gpio commands
fll - flash layout list according to settings.
iosf - Read/write 32 bit register on IOSF sideband port.
i2c - I2C buses read and write (SV ver).
ata-map - Sets the ATA geometry mapping.
cache - Manipulate the processor cache.
ping - Ping destination [Ping count number]
tftp - Download/upload file from/to server via TFTP.
ip - Configure CEFDK static IP address, Subnet Mask and Gateway address.
settings - BIOS Settings
script - Switch on/off the automatic shell script.
hwmutex - Auxiliary shell command to help check hw mutex status
load - load from storage meida.
sleep - Suspend and resume utilities
wdt - Configure watchdog timers.
npcpuonly - Triggers NPCPU only mode and sends Atom into C6
help - Displays this screen.
exit - Stops the shell.
shell>